Published papers in the period from 1996 till 2015.

 

Papers published in journals of international significance:

 

Rosić Marko, Milan Bebić „Analysis of Torque Ripple Reduction in Induction Motor DTC Drive with Multiple Voltage Vectors”, Advances in Electrical and Computer Engineering (Impact Factor: 0.64). 02/2015; 15(1):105-114. DOI: 10.4316/AECE.2015.01015

Rosić Marko, Borislav Jeftenić and Milan Bebić, „Reduction of torque ripple in DTC induction motor drive with discrete voltage vectors”, Serbian Journal of Electrical Engineering 11.1 (2014): 159-173.

L. Ristić, M. Bebić, B. Jeftenić, „Development of the algorithm for energy efficiency improvement of bulk material transport system”, ELECTRONICS, Vol. 17, No. 1, pp. 30-39, June, 2013.

B. Jeftenić, M. Bebić, L. Ristić, S. Štatkić, "Design and Selection of Belt Conveying Equipment & Systems," Chapter in Design and Selection of Bulk Material Handling Equipment and Systems: Mining, Mineral Processing, Port, Plant and Excavation Engineering (M14) vol. I, ISBN: 9788190904377, J. Bhattacharya, I ed Kolkata: Wide Publishing, 2012, p. 254, (chapter) p. 60.

L. B. Ristić, B. I. Jeftenić, „Implementation of Fuzzy Control to Improve Energy Efficiency of Variable Speed Bulk Material Transportation”, IEEE Transactions on Industrial Electronics, ISSN 0278-0046, vol. 59, pp. 2959-2969, 2012., Digital Object Identifier (DOI) 10.1109/TIE.2011.2169639

B. Jeftenić, M. Bebić, L. Ristić, S. Štatkić, "Design and Selection of Belt Conveying Equipment & Systems," Chapter in Design and Selection of Bulk Material Handling Equipment and Systems : Mining, Mineral Processing, Port, Plant and Excavation Engineering. vol. I, J. Bhattacharya, Ed., I ed Kolkata: Wide Publishing, 2012, p. 254., (chapter) p. 60

Jeftenić B., Bebić M. Realization of Rewinder with a Reduced Number of Sensors”, IEEE Transaction on Industrial Electronics, ISSN 0278-0046, Issue 8, Volume 57, Digital Object Identifier 10.1109/TIE.2009.2036638, August 2010

A. Nikolić, B. Jeftenić „Different Methods for Direct Torque Control of Induction Motor Fed From Current Source Inverter”, WSEAS Transaction on Circuits and Systems, ISSN 1109-2734, Issue 7, Volume 7, pp. 738-748, July 2008.

B. I. Jeftenić, L. B. Ristić, „Electrostatic Shaft Voltage at the Crack – Gas Compressor: the Phenomenon Analyses, Testing, Measuring and the Problem Solution”, International Review of Electrical Engineering, February 2008, ISSN: 1827- 6660, pp 23-32

A. Nikolić, B. Jeftenić, Precise Vector Control of CSI Fed Induction Motor Drive”, European Transactions on Electrical Power (ETEP), John Wiley & Sons, John Wiley & Sons, Volume 16, Issue 2, Pages 175 - 188., 2006.

M. Kostić, A. Nikolić, „Solution for higher admissible values of permanently connected capacitors to the secondary side of MV/LV transformers”, WSEAS Transaction on Circuits and Systems, ISSN 1109-2734, Issue 9, Volume 4, pp. 1146-1158, September 2005.

M. Petronijević, B.Jeftenić, N. Mitrović, V. Kostić,  Matlab/Simulink Simulation of Voltage Sags Effects on Adjustable Speed Drives”, Scietific Bulletin of „Politehnica University of Timisoara, Romania, Transactions on Automatic Control and Computer Science, ISSN 1224-600X, Vol.49(63), No. 1, 2004., pp.155-158, 2004.

V. Kostić, N. Mitrović, M. Petronijević, B.Jeftenić, „Torque Ripple Minimization in Direct Torque Controlled Induction Motor Drive Based on Duty Ratio Modulated Method, Part II”, Scietific Bulletin of „Politehnica University of Timisoara, Romania, Transactions on Automatic Control and Computer Science, ISSN 1224-600X, Vol.49(63), No. 1 , 2004., pp.87-92, 2004.

N. Mitrović, V. Kostić, M. Petronijević, B.Jeftenić, „Simulation of Direct Torque Control Schemes for Electric Drive Application, Part I”, Scietific Bulletin of „Politehnica University of Timisoara, Romania, Transactions on Automatic Control and Computer Science, ISSN 1224-600X, Vol.49(63), No. 1, 2004., pp.83-86, 2004.

B. Kolonja, D. Ignjatović, B.Jeftenić, „The application of frequency converters for the regulation of belt conveyor drives in surface mining”, International journal  ISSN 1451-107X „Transport & Logistics”, Number 5 , December 2003. (05/03), pp.11-27, 2003.

Zdravko Andonov, Borislav Jeftenić, Slobodan Mirčevski Results recurrence on genetic algorithm estimation of the induction motor equivalent scheme parameters”, Electronics, vol. 7., no 2, Banja Luka, December 2003, pp. 68. – 71.

Borislav Jeftenić, Milorad Krgović, Milan Bebić, „The Selection of Sectional Drives for the Replacement of  the Line Shaft Drive in a Paper Machine”, International journal for physics, chemistry and technology of cellulose and lignin edited by the Romanian academy Cellulose chemistry and technology, 36, 5-6,  Sept.-Oct., pp.559-565, 2002.

Borislav Jeftenić, Milorad Krgović, Milan Bebić, Mario Belinčević, „Actionarile distribuite ale unei masini de hartie”, (in Romanian) Balkan pulp and paper news, Vol. III, July 2002, pp. 26-28.

N.N. Mitrović,  M. P. Petronijević, and Vojkan Kostić, „Slip Frequency and Voltage Drop Compensation in Speed Sensorless PWM Induction Motor Drives”, Periodica Politechnica, Transaction on Automation Control and Computer Science, Vol 47, 2002, pp. 24-27.

Nebojša Mitrović, Borislav Jeftenić, Milan Bebić, Milutin Petronijević, Dragan Jevtić, „Control of AC drives without speed sensors by frequency compensation”, Electronics, vol. 4., no 1, Banja Luka, November 2000, pp. 26. – 30

Aleksandar Nikolić, Borislav Jeftenić,  „Experimental survey of the motor reference curent correction under the vector control”, Electronics, vol. 4., no 1, Banja Luka, November 2000, pp. 35 - 39

Jeftenić, B.I.; Bebić, M.Z.; Mitrović, N.N., „A simple speed sensorless control for variable frequency induction motor drives”, IEEE Transactions on Energy Conversion, Volume: 14 Issue: 3 , Sept. 1999 Page(s): 500 -505

Mataušek, M.R.; Miljković, D.M.; Jeftenić, B.I., „Nonlinear multi-input-multi-output neural network control of DC motor drive with field weakening”, IEEE Transactions on Industrial Electronics, Volume: 45 Issue: 1 , Feb. 1998 Page(s): 185 -187

Mataušek, M.R.; Jeftenić, B.I.; Miljković, D.M.; Bebić, M.Z., „Gain scheduling control of DC motor drive with field weakening”, IEEE Transactions on Industrial Electronics, Volume: 43 Issue: 1 , Feb. 1996 Page(s): 153 -162

 

Papers published in domestic journals:

 B. Jeftenić, S. Štatkić, M. Bebić, L. Ristić, „Multimotor controlled drives and energy efficiency in practice”,  Chapter in the monograph of national significance Energy efficiency of electrical drives (M45), ISBN: 978-86-7776-147-9, UDC 621 313, pp 219 - 337, Faculty of Technical Sciences in Čačak, University in Kragujevac, 2012.

B. Jeftenić, L. Ristić, M. Bebić, S. Štatkić, D. Jevtić, I. Mihailović, N. Rašić, „Realization of System of Belt Conveyors Operation with Remote Control ”, STRUCTURAL INTEGRITY AND LIFE, JOINT EDITION OF THE SOCIETY FOR STRUCTURAL INTEGRITY AND LIFE AND THE INSTITUTE FOR MATERIALS TESTING, ISSN 1451-3749, Vol 10, No 1, April 2010., UDK/UDC: 621; pp. 21-31

A. Nikolić, B. Jeftenić, „Direct torque control application in induction motor drive with current source inverter”, Elektroprivreda, The Journal of the Union of Yugoslav power industry, ISSN 0013-5755, No. 2, Year LXI, April-June 2009., UDK: 521.232; 621.3.018.5, 621.314.572 pp. 5-18

B. Jeftenić, L. Ristić, M. Bebić, „Electrostatic Shaft Voltage at the Crack – Gas Compressor: the Phenomenon Analyses, Testing, Measuring and the Problem Solution”, Energija, Journal of Power engineers Society, ISSN 0354-8651, No. 3-4, Year IX, December 2007., UDC 621.51:621.3.015, pp. 61-66

N. Mitrović, B. Jeftenić, M. Petronijević, „Double Fed Induction Motor Speed Control with Standard PWM Inverter in Stator”, Facta Universitatis, series Electronics and Energetics, vol. 10, No. 1, 1997, pp. 125-138.

B. Jeftenić, M. Petronijević and N. Mitrović, „Single Phase reversible rectifier with unity power factor”, Facta Universitatis, series Electronics and Energetics, vol. 10, No. 2, 1997, pp. 295-310.

B. Jeftenić, M. Bebić, L. Ristić, „Optimization of Energy Consumption of Board and Paper Machine”, Termotehnika, Journal of Heat Transfer Engineers, Year. XXIX, No 1-4, 2003, pp. 39-48. (UDC:676.012/.013, BIBLID:0350-218X, 29(2003), 1-4, 39-48)

L. Ristić, Z. Stojiljković, B. Jeftenić, M. Bebić, „Doubly fed induction wind generators - the state of the art”, Energija, Journal of Power engineers Society, No 2, Year IV, June 2005., UDC 620.9, pp. 224-228

B. Jeftenić, S.Statkić, M. Bebić, L. Ristić, „New concept of electrical drives for paper and board machines based on energy efficiency principles”, Thermal Science 4/2006, Journal of  Society of Thermal Engineers of Serbia and Montenegro,  Vol. 10 (Suppl.), Number 4, Belgrade 2006, pp. 1-240. (UDC:676.026.23/.25, BIBLID:0354-9836, 10(2006), Suppl., 4, 63-78)

 

Papers presented at international conferences:

L. Ristić, I. Mihailović, I. Jeftenić, A. Nikolić, M. Bebić, „Energy Efficiency in Paper Industry - Study of Two Cases”, 3rd International Symposium On Environment Friendly Energies And Applications (EFEA 2014), pp. 359-364, Paris, France, Nov, 2014.

M. Rosić, M. Božić, M. Bjekić, L. Ristić, „Electrical Motor Testing Station with Electromagnetic Load Emulator: An Overview of Design, Construction and Calibration with Examples of Use”, 3rd International Symposium On Environment Friendly Energies And Applications (EFEA 2014), pp. 371-376, Paris, France, Nov, 2014.

N. Rašić, M. Bebić, L. Ristić, B. Jeftenić, S. Štatkić, „Control of the Main Working Axes of Bucket Wheel Excavators According to the Criterion of Desired Capacity”, IECON 2013, pp. 3431-3436, IEEE Catalog Number: CFP13IEC-USB, Vienna; Austria, Nov, 2013.

L. Ristić, M. Bebić, D. Jevtić, B. Jeftenić, S. Štatkić, A. Nikolić, „Controlled multi motor drives of high power belt conveyors: Practical experiences during the exploitation of the system on open pit mine”, 13th International Conference on Electric Power Systems, High Voltages, Electric Machines (POWER '13), pp. 65-70, Recent Advances in Electrical Engineering Series 22, WSEAS Press, Chania, Crete Island, Greece, Aug, 2013.

Štatkić, S., Rašić, N., Jevtić, D., Bebić, M., Ristić, L., Jeftenić, B., „Controlled multimotor drive for crawler transport in Extreme operating conditions”, International scientific conference UNITECH ’12, ISSN 1313-230X, pp I92-I97, Gabrovo, Bulgaria16-17. Nov. 2012.

L. Ristić, M. Bebić, D. Jevtić, I. Mihailović, N. Rašić, B. Jeftenić, S. Štatkić, „Development of the algorithm for speed control of belt conveyor system on open pit mines”, In Proc. of the IX International Symposium on Industrial Electronics - INDEL 2012, ISSN/ISBN: 978-99955-46-14-4, pp. 239-246, Banja Luka, Bosnia and Herzegovina, 01-03. November 2012.

 M. Bebić, N. Rašić, S. Štatkić, L. Ristić, D. Jevtić, I. Mihailović, B. Jeftenić, „Drives and Control System for Paper-Board Cross Cutter”, In Proc. of 15th International Power Electronics and Motion Control Conference EPE-PEMC 2012, ISBN: 978-1-4673-1971-3, IEEE catalog number CFP 1234A-USB, pp LS6c.3-1- LS6c.3-8, Novi Sad, Serbia, sept. 2012.

I. Jeftenić, I. Mihailović, B. Jeftenić, „Analysis of the Drive for Horizontal Motion of a Crane Using a Laboratory Model ”, In Proc. of 15th International Power Electronics and Motion Control Conference EPE-PEMC 2012, ISBN: 978-1-4673-1971-3, IEEE catalog number CFP 1234A-USB, pp DS2a.14-1- DS2a.14-8, Novi Sad, Serbia, sept. 2012.

L.B. Ristić, M.Z. Bebić, D.S. Jevtić, I.D. Mihailović, S.Ž. Štatkić, N.T. Rašić, B.I. Jeftenić „ Fuzzy speed control of belt conveyor system to improve energy efficiency”, In Proc. of 15th International Power Electronics and Motion Control Conference EPE-PEMC 2012, ISBN: 978-1-4673-1971-3, IEEE catalog number CFP 1234A-USB, pp DS2a.9-1- DS2a.9-7, Novi Sad, Serbia, sept. 2012

S. Štatkić, M. Bebić, N. Rašić, D. Jevtić, L. Ristić, I. Mihailović, B. Jeftenić,  „Computer Integrated System for Control of Multi-Motor Crawler Drive on Open Pit Mining Machines”, In Proc. of 4th International Mining Congress BALKANMINE 2011, ISSN 978-99955-46-14-4, pp 649-655, University of Ljubljana, Faculty of Natural Sciences and Engineering, Department of Mining and Geotechnology, Slovenia 18-20. Oct. 2011.

L. Ristić, M. Bebić, S. Štatkić, I. Mihailović, D. Jevtić, B. Jeftenić „Bulk Material Transportation System in Open Pit Mines with Improved Energy Efficiency”, In Proc. of the 15th WSEAS International Conference on Systems (Part of the 15th WSEAS CSCC Multiconfrence), ISBN: 978-1-61804-023-7, ISSN: 1792-4235, Corfu Island, Greece, July 14-16, 2011, pp 327 - 332 - invited paper

B. Jeftenić, M. Bebić, L. Ristić, S. Štatkić, „Universal Control Block for Paper Machine Drives”, IEEE International Conference on Industrial Technology ICIT 2010, Print ISBN: 978-1-4244-5695-6, Digital Object Identifier: 10.1109/ICIT.2010.5472759 , pp. 445-450, Chile, 2010

S. Štatkić, B. Jeftenić, M. Bebić, „Controlled Multi Motor Crawler Drive with Adjustable Steering Radius on Open Pit Mining Machines”, In Proc. of The International Symposium on Power Electronics, Electrical Drives, Automation and Motion SPEEDAM 2010, ISBN: 978-1-4244-7919-1, IEEE catalog number CFP 1048A-`CDR, pp 947 - 952, Pisa, Italy, June 2010.

Borislav Jeftenić, Ilija Mihailović, Milan Bebić, Leposava Ristić, Dragan Jevtić, Neša Rašić, Saša Štatkić „ Energy efficiency in transportation of bulk material with frequency controlled drives”, In Proc. of 14th International Power Electronics and Motion Control Conference EPE-PEMC 2010, ISBN: 978-1-4244-7854-5, IEEE catalog number CFP 1034A-DVD, pp T5 105-113, Ohrid, Macedonia, Sept. 2010.

B. Jeftenić, L. Ristić, M. Bebić, S. Štatkić, I. Mihailović, D. Jevtić „Optimal Utilization of the Bulk Material Transportation System based on Speed Controlled Drives”, In Proc. of The XIX International Conference on Electrical Machines ICEM 2010, ISBN: 978-1-4244-4175-4, IEEE catalog number CFP 1090B-CDR, RF-009709, pp 1 - 6, Rome, Italy, Sept. 2010.

Borislav Jeftenić, Leposava Ristić, Milan Bebić, Saša Štatkić, „Controlled Induction Motor Drives Supplied by Frequency Converters on Belt Conveyors – Modeling and Commissioning”, IEEE-IECON 2009 - THE 35th ANNUAL CONFERENCE OF THE IEEE INDUSTRIAL ELECTRONICS SOCIETY, in IEEE Proceedings volume and included in IEEE Xplorer and indexed by EI Compendex , November 3-5, 2009, Porto, Portugal.

Borislav Jeftenić, Milan Bebić, Leposava Ristić, Dragan Jevtić, Ilija Mihailović, Neša Rašić, Saša Štatkić, „Basic concept of remote control of multi motor drive of belt conveyor with uniform load distribution”, In CD Proc. Program of 15th International Conference on ELECTRICAL DRIVES and POWER ELECTRONICS, 12 – 14 October 2009, Dubrovnik, Croatia.

Borislav Jeftenić, Leposava Ristić, Milan Bebić, Neša Rašić, „New solution of tangent rewinder drive in the board factory”, ICEM'08- XVIII International Conference on Electrical Machines, Vilamoura (Algarve), Portugal, 2008.

B. Jeftenić, M. Bebić, M. Gvozdenović, N. Rašić, L. Ristić, D. Jevtić, P. Lučić, D. Slavković, „Load Equalization for High-Power Induction Motors by Speed Control in Limited Range”, In Proc. of The International Symposium on Power Electronics, Electrical Drives, Automation and Motion SPEEDAM 2008, Ischia, Italy

A. Nikolić, B. Jeftenić, Fixed-point DSP algorithm for flux vector estimation in DTC IM drive in Proceedings of the IEEE Region 8 EUROCON Conference EUROCON 2005, Belgrade, Serbia & Montenegro, November 21-24, 2005.

M. Kostić, A. Nikolić, Procedure for capacitor utilization improvement intended for reactive power compensation in networks with high order harmonics, in Proceedings of the 5th WSEAS International Conference on Power Systems and Electromagnetic Compatibility, Corfu, Greece, August 2005.

A.Nikolić, B.Jeftenić, „Speed Sensorless Direct Torque Control Implementation in a Current Source Inverter Fed Induction Motor Drive”, in Proceedings of the 35th Annual IEEE Power Electronics Specialists Conference, 20-25 June, 2004., Aachen, Germany, pp.2843-2848.

Borislav Jeftenić, Miodrag Milojević, Milan Bebić, Leposava Ristić, „New drive and control strategy of the board machine in board factory „Umka” Serbia”, 10th Meeting of Pulp and Paper Industry of Balkan (Southeast European) Countries, 29th – 31st October 2003. Thessaloniki, Greece

A.Nikolić, B.Jeftenić, „DTC of a CSI-Fed Induction Motor with DC Link Based Adaptive Estimator”, in Proceedings of the 28th IEEE Industrial Electronics Society Conference IECON 2002

Dejan Reljić, Veran Vasić, Borislav Jeftenić, „Kočenje asinhronog motora jednosmernim strujama”  IV Simpzijum Industrijska elektronika INDEL-2002, pp 183-186, Banja Luka, 14-15 novembar 2002.

Nebojša Mitrović, Milutin Petronijević, Borislav Jeftenić, Vojkan Kostić, „Steady State Speed Error Reduction in Sensorless PWM Induction Motor Drives”, Proc. of  XXXVII Int. Science Conf. - ICEST, Niš, 2002, pp.692-695.

Milutin Petronijević, Borislav Jeftenić, and Nebojša Mitrović, „Application of the 3-Phase Power Factor Correction Rectifier in DC Drive ”, Proc. of  XXXVII Int. Science Conf. - ICEST, Niš, 2002, pp.385-388.

M. Ćalović, A. Nikolić, Underfrequency Load Shedding - A Case Study, in Proceedings of the 12th International Conference on Power System Protection PSP2000, Bled, Slovenia, 27th September, 2000.

Borislav Jeftenić, Milorad Krgović, Milan Bebić, „The Selection of Sectional Drives for Replacement Of The Line Shaft Drive In A Paper Machine”, VII International Balcan Pulp and Paper Industry Conference, Novi Sad, 2000.

A.Nikolić, B.Jeftenić, „Software Routine for Automatic Fine-tuning of the Rectifier Synchronization to AC Line Voltages”, in Proceedings of the IX Power Electronics and Motion Control Conference EPE-PEMC’2000, Kosice, Slovak Republic, 5th September 2000.

A.Nikolić, B.Jeftenić, „Experimental Methods for Performance Analysis of the Vector Controlled Induction Motor Drives”, in Proceedings of the V National Conference for Electronics, Telecomunications, Automation and Informatics ETAI 2000 and II International Symposium on Applied Automatic Systems AAS’2000, Ohrid, Macedonia, 21st September 2000.

A.Nikolić, „Digital Protection Algorithm Based On a Simple Microcontroller Circuit”, in Proceedings of the 12th International Conference Power System Protection PSP2000, Bled, Slovenia, 27th September 2000.

Nikolić, A.B.; Jeftenić, B.I., „A microcontroller based control of current source converter fed reversing induction motor drive”, International Conference on Electric Power Engineering, 1999. PowerTech Budapest 99. 1999, Page(s): 111

Milan Bebić, Borislav Jeftenić, „Fuzzy Logic Speed Controller for a Variable Frequency AC Drive System”, PEMC’98, Proceedings of the 8th International Power Electronics & Motion control conference, 8-10 September, 1998, Prague, Czech Republic

A. Nikolić, B. Jeftenić, „The New Algorithm for Vector Controlled CSI Fed Induction Motor Drive”, PEMC’98, Proceedings of the 8th International Power Electronics & Motion control conference, 8-10 September, 1998, Prague, Czech Republic

Nebojša Mitrović, Borislav Jeftenić, Milutin Petronijević, „PSPICE Model For Three Phase Induction Motor ”, Proc. of  III Intern. Conf. on Risk in Technological Systems and Environment, Niš, 1997, pp.77-80.

Nebojša Mitrović, Borislav Jeftenić, Milutin Petronijević, „Modelling a Variable Frequency Induction Motor Drive”, Proc. of  III  Intern. Conf. on Risk in Technological Systems and Environment, Niš, 1997, pp.81-84.

A.Nikolić, B.Jeftenić, „The New CSI Control Strategy For Avoiding Slow Response In Vector Controlled Induction Motor Drive”, in Proceedings of the VII European Power Electronics and Drives Conference EPE’97, Trondheim, Norway, September 1997

Nebojša Mitrović, Borislav Jeftenić, Dobrivoje Stojanović, Milutin Petronijević, „Parameter Identification Technique for Inverter Fed Induction Motor”, International Conference on Technical Informatics, ConTI 96, Timisoara, Romania, November 14-16, 1996, Vol. 2, pp. 145-152.

Jeftenić, B.; Milosavljević, S.; Mitrović, N.; Rodić, M. „Speed control in inverter induction motor drives based on only one current sensor”, 27th Annual IEEE Power Electronics Specialists Conference, 1996. PESC ’96 Record, Volume: 1 , 1996, Page(s): 364 -369 vol.1

B.Jeftenić, N.Mitrović, S.Milosavljević, M.Rodić, „Low cost speed sensorless control in PWM induction motor drives”, PEMC 96, Budapest, Hungary, 2-4 sept. 1996, vol 2, pp. 489 - 494

A.Nikolić, B.Jeftenić, „Computer simulation analysis of vector controlled CSI fed induction motor drive”, PEMC 96, Budapest, Hungary, 2-4 sept. 1996, vol 2 pp. 537 - 542

 

Papers presented at domestic conferences:

 L. Ristić, N. Rašić, D. Jevtić, I. Mihailović, M. Bebić, B. Jeftenić, S. Štatkić, „Realization of system of mining machines with improved efficiency on open pit mines - driving and control”, X international symposium - RESEARCH AND DESIGN FOR INDUSTRY, pp. 220-241, Institute for research and design in commerce&industry, Belgrade, December, 2014.

N. Rašić, S. Štatkić, L. Ristić, M. Bebić, „High harmonics cancellation in multimotor drives with rigid coupling ”, 57. Conference ETRAN, Etran Society, Zlatibor, 2013.

I. Jeftenić, M. Bebić,  „Opservacija ugla njihanja tereta usled horizontalnog pomeranja krana”, In Proc. of the 56. ETRAN Conference,  ISBN 978-86-80509-67-9, pp EE1.3-1-4- EE1.3-1-8, Zlatibor, June 11-14th ,2012.

I. Mihailović, M. Bebić,  „Korišćenje laboratorijskog simulatora opterećenja za analizu rada pogona sa dugačkim vratilom”, In Proc. of the 56. ETRAN Conference,  ISBN 978-86-80509-67-9, pp EE1.4-1-4- EE1.4-1-8, Zlatibor, June 11-14th ,2012.

B. Jeftenić, L. Ristić, I. Mihailović, D. Jevtić, M. Bebić, S. Štatkić, N. Rašić „Application of energy efficient technologies in bulk material transportation - possibilities and practical expiriences”, In proc. of the II Regional Conference of industrial energy and environmental protection in Southeastern Europe - IEEP 2010, ISBN 978-86-7877-012-8, pp 1-8, Zlatibor, 22.-26. jun 2010.

Miroslav Ivković, Tomislav Manojlović, Taško Maneski, Borislav Jeftenić, Marina Terzić, „Revitalization of SRs1300 bucket wheel excavator on Drmno Open pit mine“, Mechanization and automation in mining and energetics - MAREN 2010, ISBN 978-86-7352-210-4, pp 339-350, Lazarevac, 16-18.6.2010.

B. Jeftenić, N. Rašić, M. Bebić, D. Jevtić, S. Štatkić, I. Mihailović, L. Ristić, „Revitalization and modernization of control and drive systems for mining machines on Open pit mine Drmno during the period 2002-2010.“ Mechanization and automation in mining and energetics - MAREN 2010, ISBN 978-86-7352-210-4, pp 322-338, Lazarevac, 16-18.6.2010.

B. Jeftenić, N. Rašić, D. Jevtić, M. Bebić, I. Mihailović, L. Ristić, S. Štatkić, „Design and realization of newmining machines on Open pit mine Drmno - electrical subsystem“ Mechanization and automation in mining and energetics - MAREN 2010, ISBN 978-86-7352-210-4, pp 81-91, Lazarevac, 16-18.6.2010.

B. Jeftenić, M. Bebić, N. Rašić, D. Jevtić, I. Mihailović, L. Ristić, V. Ilić, M.Zindović, „New electric drive for paper machine in Fabrika Hartije Beograd“, In Proc. of XVI INTERNATIONAL SYMPOSIUM IN THE FIELD OF PULP, PAPER, PACKAGING AND GRAPHICS CPA&G, ISBN 978-86-7401-267-3, pp 41-49, Zlatibor, 15-18.6.2010.

Borislav Jeftenić, Leposava Ristić, Milan Bebić, Saša Štatkić, Neša Rašić, Dragan Jevtić, Milorad Gvozdenović „Development of the algorithm for speed control of the system of belt conveyors”, XV  International Symposium on Power Electronics – Ee 2009 Novi Sad,  October 28th-30th , 2009.

B. Jeftenić, M. Bebić, L. Ristić, D. Jevtić, I. Mihailović, N. Rašić, S. Štatkić „Remote supervision and control of the system of belt conveyors”, XV  International Symposium on Power Electronics  – Ee 2009 Novi Sad, October 28th-30th , 2009.

B. Jeftenić, M. Bebić, L. Ristić, D. Jevtić, N. Rašić, S. Štatkić, D. Ignjatović, Application of modern controlled drives on mining machinery ”, III international symposium ELEKTRANE, Vrnjačka Banja, 28.-31.10.2008., In procc. on CD, ISSN: 978-86-7877-011-1, pp.1-10

B. Jeftenić, M. Bebić, L. Ristić, S. Štatkić, D. Jevtić, N. Rašić, Retrospective of development of electromotor drives in paper industry in our country during last ten years and plans for the future, In proceedings of  XV International symposium in the field of pulp, paper, packaging and graphics CPA&G, ISBN 978-86-7401-259-8, pp. 41-49, Zlatibor, 2009.

B. Jeftenić, M. Bebić, L. Ristić, D. Jevtić, N. Rašić, S. Štatkić, D. Ignjatović, „Application of Modern Controlled  Drives on Open Pit Mining Machines”, III International Symposium POWER PLANTS, Vrnjačka Banja, 28.-31.10.2008.

B. Jeftenić, L. Ristić, M. Bebić, N. Rašić, „New Supervision System for Tangent Rewinder in Board Factory  „Umka” ”, XIV INTERNATIONAL SYMPOSIUM IN THE FIELD OF PULP, PAPER, PACKAGING AND GRAPHICS CPA&G, Zlatibor, 2008.

M. Bebić, B. Jeftenić, D. Jevtić, N. Rašić, L. Ristić, S. Štatkić „Application of controlled motor drives supplied by frequency converters on belt conveyors”, XIV International Symposium on Power Electronics - Ee 2007, Novi Sad, November 2007.

B. Jeftenić, L. Ristić, M. Bebić, V. Kostić, N. Mitrović, „Modern control techniques of  pumps for dewatering on open pit mines”, XIV International Symposium on Power Electronics - Ee 2007, Novi Sad, November 2007.

B.Jeftenić, M. Gvozdenović, L. Ristić, M. Bebić, D. Jevtić, P. Lučić, D. Slavković, M. Milošević „Load equalization for high power induction motors by step control in restricted range”,  In Proceedings of 28. Symposium JUKO CIGRE, Book II, Sections B1, B2, B4, pp. 245-254, Vrnjačka Banja, 30.09-05.10.2007.god.

B. Jeftenić, N. Rašić, M. Bebić, M. Belinčević, „Reconstruction and modernization of tangent rewinder in Board factory „UMKA””, 12th INTERNATIONAL SYMPOSIUM IN THE FIELD OF PULP, PAPER, PACKAGING AND GRAPHICS, Zlatibor, 2006.

Vladimir Ćuk, Aleksandar Nikolić, Borislav Jeftenić, „Application of controlled electrical drives in pumping stations of the water supplying systems,  L Conference ETRAN, Belgarde, 6th-8th June, 2006.

Neša Rašić, Borislav Jeftenić, Milan Bebić, Saša Štatkić, Controlled bucket wheel drive on the excavator SRs 1300,  L Conference ETRAN, Belgarde, 6th-8th June, 2006.

Dragan Jevtić, Borislav Jeftenić, „New electrical drive of overhead cranes in the Hydro Power Plant Đerdap I,  L Konferencija ETRAN-a, L Conference ETRAN, Belgarde, 6th-8th June, 2006.

Neša Rašić, Borislav Jeftenić, Saša Štatkić, Multi motor controlled drive on the transport of bucket wheel excavator SRs 2000,  L Conference ETRAN, Belgarde, 6th-8th June, 2006.

V. Kostić, N. Mitrović, M. Petronijević, B. Jeftenić An solution for transport bridge bevelling elimination and correction in TE-TOSenta Sugar-refinery”, 30. Scientific-expert meeting with international participation ”HIPNEF 2006 , pp. 195-200, Vrnjačka Banja, 2006.

Zdravko Andonov, Borislav Jeftenić, Slobodan Mirčevski, „ Induction Motor Temperature Estimation Using Genetic Algorithm”,  XIII International Symposium on Power Electronics - Ee 2005, Novi Sad, November 2005.

Saša Štatkić, Neša Rašić, Borislav Jeftenić, Multi motor controlled drives on the transport of mining machines”, XIII International Symposium on Power Electronics - Ee 2005, Novi Sad, November 2005.

Dragan Jevtić, Borislav Jeftenić, Electrical drives modernization of overhead cranes in the Hydro Power Plant Đerdap I”, XIII International Symposium on Power Electronics - Ee 2005, Novi Sad, November 2005.

Milan Bebić, Borislav Jeftenić, Dragan Ignjatović, Mathematical modeling of the conveyor belt”, XIII International Symposium on Power Electronics - Ee 2005, Novi Sad, November 2005.

Vladan R. Jevremović, Borislav Jeftenić, An Efficient Breaking Algorithm for Interior Permanent Magnet Syncronous Motors”, XIII International Symposium on Power Electronics - Ee 2005, Novi Sad, November2005.

Vladan R. Jevremović, Borislav Jeftenić, „State of the art of cascade speed control loops in alternating current motor drives”, XIII International Symposium on Power Electronics - Ee 2005, Novi Sad, November 2005.

A. Nikolić, B. Jeftenić, „A method for flux vector detection in DTC drives”, XIII International Symposium on Power Electronics - Ee 2005, Novi Sad, November 2005.

A. Nikolić, D. Mišović, „Digital system tuning with the help of real time simulations”, XIII International Symposium on Power Electronics - Ee 2005, Novi Sad, November2005.

L. Ristić, Z. Stojiljković, B. Jeftenić, M. Bebić, „Doubly fed induction wind generators - the state of the art”, Energetika 2005, Zlatibor 19-22. June 2005., (Proc. on CD), SCG, 2005.

Nebojša Mitrović, Vojkan Kostić, Milutin Petronijević,  Borislav Jeftenić, „Simulation of DTC of induction motor with compensation of stator resistance variations”  YU INFO 2005, XI Conference, Kopaonik, 07-11 march 2005.god. (Proc. of abstracts pp.129, Proc. of papers on CD), SCG, 2005.

Milan Bebić, Borislav Jeftenić, Leposava Ristić, „Electric Drives in Paper Machines”, 3. Meeting in the organization of the SCG Thermal engineers Society  „Industrial energetics 2004”, Lepenski Vir, 28.09. - 02.10. 2004., SCG, 2004.

Leposava Ristić, Zoran Stojiljković, Borislav Jeftenić, „The state of  the art in the field of generator scheme development for  wind generators connection to the standard distribution network”, Proc. of 3. scientific meeting The alternative energy sources and the future of their application in our country, Budva, SCG, 9-10. October 2003., Scientific meetings Book 65, Department of natural sciences Book 8, pp.117-122

A. Nikolić, B. Jeftenić, „Control strategies in current source inverter fed drives”, XII International Symposium on Power Electronics - Ee 2003, Novi Sad, November 2003.

Borislav Jeftenić, Milan Bebić, Leposava Ristić, Radivoje Mitrović, „Effects of application of controlled induction motor drives with frequency converters in the revitalization of existing drives”, XII International Symposium on Power Electronics - Ee 2003, Novi Sad, November 2003.

Borislav Jeftenić, Milan Bebić, Leposava Ristić, „Optimization of energy consumption of board and paper machine”, XII International Symposium on Power Electronics - Ee 2003, Novi Sad, November 2003.

Milutin Petronijević, Nebojša Mitrović, Borislav Jeftenić, „Load distribution in multi motor drives with mechanical coupling”  XLVII  Conference ETRAN, Herceg Novi, June 8th-13th 2003.

Borislav Jeftenić, Milan Bebić, Leposava Ristić, Radivoje Mitrović, „Techno-economic advantages of controlled induction motor drives with frequency converters”,  XLVII  Conference ETRAN, Herceg Novi, June 8th-13th 2003.

Borislav Jeftenić, Miodrag Milojević, Milan Bebić, Mario Belinčević, „Novi pogon karton mašine u fabrici kartona „Umka” II deo”, IX Jugoslovenski simpozijum iz oblasti celuloze, papira, ambalaže i grafike, pp. 89 - 97, Zlatibor, 17 - 20 juna 2003.

M. Petronijević, B. Jeftenić, N. Mitrović, „Istraživanje uticaja frekventnih pretvarača na distributivnu mrežu”, XXVI Savetovanje Juko Cigre,  Grupa 14: Jednosmerni prenos i oprema energetske elektronike, pp. R 14-08, Banja Vrućica, 25 - 30 maja 2003.

Milorad Krgović, Borislav Jeftenić, Voislav Ristovski, Milovan Jovanović, Mario Belinčević, „Efekti rekonstrukcije papir mašine u Komuni Skopje i izgradnje tissue mašine u Papirpaku Čačak”, VIII Jugoslovenski simpozijum iz oblasti celuloze, papira, ambalaže i grafike, pp. 153 - 164, Zlatibor, 26 - 28 juna 2002.

Borislav Jeftenić, Miodrag Milojević, Milan Bebić,Mario Belinčević, „Novi pogon karton mašine u fabrici kartona „Umka” I deo”, VIII Jugoslovenski simpozijum iz oblasti celuloze, papira, ambalaže i grafike, pp. 147 - 152, Zlatibor, 26 - 28 juna 2002.

Dejan Reljić, Veran Vasić, Borislav Jeftenić, „Statičke mehaničke karakteristike asinhronog motora pri kočenju jednosmernim strujama”  XLVI Konf. za ETRAN, tom I, pp. 283-286, Banja Vrućica – Teslić, 4-7 juna 2002

V. Kostić, N. Mitrović, M. Petronijević, „Primena frekvencijskih pretvarača u dizaličnim pogonima”, 28. NSS ”HIPNEF 2002” , pp. 257-262, Vrnjačka Banja, 2002.

Aleksandar Nikolić, Borislav Jeftenić, „Rekonstrukcija napona i struje asinhronog motora u pogonu sa strujnim invertorom”, ETRAN, XLV Konferencija, Aranđelovac, 4-6 jun 2001

Leposava Ristić, Milan Bebić, Predrag Ristić, „Savremene metode za nadgledanje i upravljanje industrijskim procesima”, ETRAN, XLV Konferencija, Aranđelovac, 4-6 jun 2001

Borislav Jeftenić, „Višemotorni regulisani pogoni”, XI Simpozijum Energetska Elektronika, Novi Sad, 31.10-2.11.2001.

Milan Bebić, Borislav Jeftenić, Mario Belinčević, „Elektromotorni pogoni papir mašina”, XI Simpozijum Energetska Elektronika, Novi Sad, 31.10-2.11.2001.

Borislav Jeftenić, Milan Bebić, Dragan Jevtić, „Raspodela opterećenja kod pogona u mehaničkoj sprezi”, XI Simpozijum Energetska Elektronika, Novi Sad, 31.10-2.11.2001.

Aleksandar Nikolić, „Savremena rešenja za analizu upravljanja motornim pogonima”, XI Simpozijum Energetska Elektronika, Novi Sad, 31.10-2.11.2001.

Aleksandar Nikolić, Borislav Jeftenić, „DTC metoda kod asinhronog motora sa strujnim invertorom”, XI Simpozijum Energetska Elektronika, Novi Sad, 31.10-2.11.2001.

Aleksandar Nikolić, Borislav Jeftenić, „Estimacija fluksa asinhronog motora merenjem u DC kolu”, XI Simpozijum Energetska Elektronika, Novi Sad, 31.10-2.11.2001.

Mario Belinčević, Milan Bebić, Borislav Jeftenić, „Upravljački algoritam za sinhronizaciju rada pogona letećih makaza”, XI Simpozijum Energetska Elektronika, Novi Sad, 31.10-2.11.2001.

Zoran Marković, „Elektromotorni pogon tangentnog premotača”, XI Simpozijum Energetska Elektronika, Novi Sad, 31.10-2.11.2001.

Borislav Jeftenić, Mario Belinčević, Milan Bebić, Dragan Jevtić, „Zamena mehaničke transmisije papir mašine pojedinačnim asinhronim pogonima”, VII Jugoslovenski simpozijum iz oblasti celuloze, papira, ambalaže i grafike, pp. 73 - 79, Zlatibor, 20 - 22 juna 2001.

Milan Bebić, Borislav Jeftenić, Mario Belinčević, „Testiranje tačnosti sinhronizacije pogona letecih makaza u praznom hodu”, ETRAN, XLV Konferencija, Aranđelovac, 4-6 jun 2001

M. Petronijević, N. Mitrović, „Elektromagnetna kompatibilnost asinhronih pogona sa PWM pretvaračem”, XLV Konferencija ETRAN-a, Aranđelovac, Jun 2001.

Mario Belinčević, „Uštede u potrošnji energije upotrebom frekventnih pretvarača”, VII Jugoslovenski simpozijum iz oblasti celuloze, papira, ambalaže i grafike, pp 130 - 138, Zlatibor, 14 - 16 juna 2000.

Borislav Jeftenić, Miodrag Milojević, Milan Bebić, Dragan Jevtić, „Rekonstrukcija elektromotornih pogona poprecnog rezača na bazi primene frekventnih pretvarača”, VII Jugoslovenski simpozijum iz oblasti celuloze, papira, ambalaže i grafike, pp 130 - 138, Zlatibor, 14 - 16 juna 2000.

D. Stojanović, N. Mitrović, M. Petronijević, L. Matić „Simulacija dinamike generatora sa uvažavanjem regulacije pobude”, YU Info 2000, Zbornik radova na CD-u,  Kopaonik, 27-31. 03. 2000.

M. Petronijević, B. Jeftenić, B. Jovanović, M. Bebić, „Eksperimentalna istraživanja na ispravljaču za popravku faktora snage u jednosmernom pogonu”, X Simpozijum Energetska Elektronika Novi Sad, 14-16. 10. 1999.

D. Jevtić, B. Jeftenić, M. Gvozdenović, M. Rodić, „Realizacija monofaznog stabilizatora mrežnog napona”, X Simpozijum Energetska Elektronika Novi Sad, 14-16. 10. 1999.

A. Nikolić, B. Jeftenić, „Eksperimentalni prikaz korekcije referentne struje motora pri vektorskom upravljanju”, X Simpozijum Energetska Elektronika Novi Sad, 14-16. 10. 1999.

N. Mitrović, B. Jeftenić, M. Bebić, M. Petronijević, D. Jevtić, „Upravljanje asinhronim pogonima bez senzora brzine kompenzacijom učestasnosti”, X Simpozijum Energetska Elektronika Novi Sad, 14-16. 10. 1999.

S. Avramović, B. Jeftenić, M. Bebić, D. Jevtić, N. Mitrović, M. Petronijević, „Istraživanja na razvoju mikroprocesorskog sistema za startovanja sinhronih motora”, X Simpozijum Energetska Elektronika Novi Sad, 14-16. 10. 1999.

Aleksandar Nikolić, Borislav Jeftenić, „Eksperimentalno podešavanje vremenske konstante rotora pri vektorskom upravljanju pogona sa asinhronim motorom”, ETRAN, XLIII Konferencija, Zlatibor, 20-22. 9. 1999., pp 315-318

M. Petronijević, N. Mitrović, B. Jeftenić, M. Bebić, „Primena SPICE-a za simulaciju električnih mašina naizmenične struje”, ETRAN, XLII Konferencija, Vrnjačka Banja, 2-5. juna 1998.

M. Bebić, B. Jeftenić, N. Mitrović, „Rekonstrukcija faznih struja asinhronog motora napajanog iz PWM invertora merenjem u jednosmernom međukolu”, ETRAN, XLII Konferencija, Vrnjačka Banja, 2-5. juna 1998.

Borislav Jeftenić, Milutin Petronijević, Nebojša Mitrović, „Aspekti razvoja regulisanih elektro pogona kao racionalnih i kvalitetnih potrošača ”, IV Skup Trendovi razvoja: „Nove tehnologije u elektrodistribuciji”, Kopoanik 09. -12.03.1998., str. 83-86.

B. Jeftenić, „Pregled primene simulacionih programa u analizi savremenih elektromotornih pogona”,  IX Simpozijum Energetska Elektronika, Novi Sad, 22-24.10.1997.

M. Petronijević, B. Jeftenić, N. Mitrović, „Analiza tranzijentnih režima u havarijskim stanjima kod ispravljača sa kontrolisanim faktorom snage”, IX Simpozijum Energetska Elektronika, Novi Sad, 22-24.10.1997.

M. Petronijević, B. Jeftenić, D. Stojanović, N. Mitrović, „Analiza uticaja snažnih poluprovodničkih pretvarača na distributivnu mrežu”, IX Simpozijum Energetska Elektronika, Novi Sad, 22-24.10.1997.

S. Štatkić, B. Jeftenić, „Analiza uticaja strujne greške na vektorsko upravljanje asinhronim motorom”, IX Simpozijum Energetska Elektronika, Novi Sad, 22-24.10.1997.

A. Nikolić, B. Jeftenić, „Realizacija mikroprocesorski upravljanog asinhronog pogona sa strujnim invertorom”, IX Simpozijum Energetska Elektronika, Novi Sad, 22-24.10.1997.

M. Marković, B. Jeftenić, M. Bebić, S. Avramović, „Funkcije prenosa asinhronog motora sa idealnim invertorom”, IX Simpozijum Energetska Elektronika, Novi Sad, 22-24.10.1997.

B. Jeftenić, M. Bebić, D. Jevtić, M. Marković, S. Avramović, S. Milosavljević, „Supstitucija analognog upravljanja tiristorskim ispravljačem digitalnim kontrolerom”, IX Simpozijum Energetska Elektronika, Novi Sad, 22-24.10.1997.

S. Milosavljević, B. Jeftenić, I. Lukić, M. Bebić, „Savremene metode vežbanja u Laboratoriji za elektromotorne pogone”, IX Simpozijum Energetska Elektronika, Novi Sad, 22-24.10.1997.

Milutin Petronijević, Borislav Jeftenić, Nebojša Mitrović, „Monofazni energetski ispravljač sa kontrolisanim faktorom snage”, XLI Konferencija ETRAN-a, Zlatibor, Jun 1997, sv.1, str. 542-545.

D. Stojanović, N. Mitrović, M. Petronijević, M. Veselinović, „Simulacija zemljospoja u srednjenaponskim distributivnim mrežama”, YU INFO’97, Brezovica, str. 499-502, 1997.

N. Mitrović, B. Jeftenić, Đ. Vukić, M Petronijević, „Voltage PWM Inverter Application for Double Fed Induction Motor Control”, 5th International Conference, Tesla III Millennium, Beograd, Yugoslavia, October 15-18, 1996, Proc. Vol.1, pp. II-97-104.

Nebojša Mitrović, Milutin Petronijević, Borislav Jeftenić, „Kompleksna analiza pogona PWM invertor - asinhroni motor”, XL Konferencija ETRAN-a, Budva, Jun 1996, str. 647-650.

Milutin Petronijević, Borislav Jeftenić, Nebojša Mitrović, „Trofazni mostni PWM ispravljač u pogonu sa jednosmernim motorom”, XL Konferencija ETRAN-a, Budva, Jun 1996, str. 643-646.

Nebojša Mitrović, Milutin Petronijević, Borislav Jeftenić, „Pspice u simulaciji složenih elektromehaničkih sistema”, YUINFO’96, Brezovica, 1996.

S.Milosavljević, B.Jeftenić, A.Nikolić, D.Jevtić, „Upravljanje pogonom za pozicioniranje sa stalnim trzajem”, V međunarodna konferencija Tesla III Millennium, Vol.2, pp.135-140, Beograd, Oktobar 1996.